Epoxy Flooring for Industrial Floors in Malaysia: EPILOX 246 SL

EPILOX 246 SL is a two-component, solvent-free epoxy flooring coating from Chemind. It is a low-viscosity resin supplied as a pre-weighed base and hardener, and it can be applied from a minimum thickness of 0.5 mm in a single application.

Where it is used

EPILOX 246 SL suits self-smoothing and broadcast systems on concrete and cement screeds, from normal wear up to medium heavy wear. It gives a hard-wearing, abrasion-resistant finish for floors such as:

  • Production facilities
  • Car parks and workshops
  • Laboratories
  • Hospitals

Why buyers specify it

  • Strong bond to sound concrete: in pull-off tests the concrete failed before the coating
  • Very low odour, because it is solvent free
  • Slip-resistant textures, using a range of Chemind Anti-slip Grains
  • Good abrasion resistance to foot and light vehicular traffic

Three ways to lay it

SystemBuild-up
Thin-film coatingEPIPRIME primer at 0.15 to 0.20 kg/m² (minimum 100 microns), then EPILOX 246 SL at 0.30 to 0.40 kg/m² (minimum 300 microns) by brush or roller, spike-rolled to release air
Self-levellingEPILOX 246 SL spread by steel trowel at 2.5 to 3.0 kg/m², minimum thickness 2 mm
Broadcast (anti-slip)EPIPRIME, a sealer coat of EPILOX 246 SL, quartz sand (0.1 to 0.3 mm) at about 1.0 kg/m², then a seal coat at 0.7 kg/m²; film about 1.5 to 3.0 mm

Technical properties

PropertyResultTest standard
Solid contentAbout 100% by weight—
Compressive strength44.5 N/mm² (average)BS 6319 Part 2:1983
Flexural strength15.6 N/mm² (average)BS 6319
Surface hardness36.8 N/mm² (average)BS EN 13892
Bond strength (pull-off)2.29 N/mm² (average). Failure was in the concrete, not the coating.BS EN 13892
Abrasion resistance57.25 mg weight loss (CS10 wheel, 1000 g load)ASTM D4060
Water vapour transmission0.22 g/h/m²ASTM E96
VOC content7.74 g/LASTM D3960

Chemical resistance

Tested with hydrochloric acid 10%: no damage apart from discolouration. This is the only chemical tested so far. If your floor will be exposed to other chemicals, oils or grease, check with Chemind's technical department before you specify.

Working times

At 20 °CAt 30 °C
Pot life40 minutes20 minutes
Time between coatsUp to 24 hoursUp to 15 hours
Light traffic24 hours18 hours
Full traffic48 hours24 hours
Full cureAbout 7 daysAbout 5 days

Times are approximate and change with ambient conditions.

Before you specify: substrate and site conditions

  • Concrete must be sound, with compressive strength of at least 25 N/mm² and pull-off strength of at least 1.5 N/mm²
  • Prepare the surface mechanically; Chemind recommends shot blasting or scarifying, not acid etching
  • Not for substrates with rising damp or relative humidity above 80%
  • Not to be applied below 10 °C or where ambient humidity exceeds 85%
  • Keep substrate and uncured floor at least 3 °C above dew point

Supply

Pack: 6.5 kg set (5 kg Part A, 1.5 kg Part B). Colours: standard flooring colours and clear, with other colours matched on request. Shelf life: up to 12 months in unopened packs stored below 35 °C.

Next step

Send us your floor area, use and site conditions, and our technical team will recommend the right EPILOX 246 SL system.

Get in touch

Talk to a waterproofing specialist

Tell us about your project and our technical team will recommend the right system and send you a quotation.

WhatsApp us